收藏本站
CS5467
5. PIN DESCRIPTIONS
5.1 Analog Pins
The CS5467 has four differential inputs: VIN1 ??? VIN2 ??
IIN1 ? , and IIN2 ? are the voltage1, voltage2, current1,
and current2 inputs, respectively. A single-ended power
fail monitor input, voltage reference input, and voltage
reference output are also available.
5.1.1 Voltage1 & Voltage2 Inputs
The output of the line voltage resistive divider or trans-
5.1.6 Crystal Oscillator
An external quartz crystal can be connected to the XIN
and XOUT pins as shown in Figure 7 . To reduce system
cost, each pin is supplied with an on-chip, phase-shift-
ing capacitor to ground.
.
XOUT
former is connected to the VIN1+ (VIN2+) and VIN1-
(VIN2-) input pins of the CS5467. The voltage channel
is equipped with a 10x, fixed-gain amplifier. The
full-scale signal level that can be applied to the voltage
channel is ±250 mV. If the input signal is a sine wave,
the maximum RMS voltage is
250 mVp / ? 2 ? 176.78 mVRMS which is approximate-
ly 70.7% of maximum peak voltage.
5.1.2 Current1 & Current2 Inputs
XIN
DGND
C1
C2
Oscillator
Circuit
C1 = C2 = 22 pF
The output of the current-sensing resistor or transform-
er is connected to the IIN1+ (IIN2+) and IIN1- (IIN2-) in-
put pins of the CS5467. To accommodate different
current-sensing elements, the current channel incorpo-
rates a programmable gain amplifier (PGA) with two se-
lectable input gains. The full-scale signal level for the
current channels is ±50 mV or ±250 mV. If the input sig-
nal is a sine wave, the maximum RMS voltage is
35.35 mVRMS or 176.78 mVRMS which is approxi-
mately 70.7% of maximum peak voltage.
5.1.3 Power Fail Monitor Input
An analog input (PFMON) is provided to determine
when a power loss is imminent. By connecting a resis-
tive divider from the unregulated meter power supply to
the PFMON input, an interrupt can be generated, or the
Low Supply Detected (LSD) Status register bit can be
monitored to indicate low-supply conditions. The PF-
MON input has a comparator that trips around the level
of the voltage reference input (VREFIN).
5.1.4 Voltage Reference Input
The CS5467 requires a stable voltage reference of
2.5 V applied to the VREFIN pin. This reference can be
supplied from an external voltage reference or from the
VREFOUT output. A bypass capacitor of at least 0.1 ? F
is recommended at the VREFIN pin.
5.1.5 Voltage Reference Output
The CS5467 generates a 2.5 V reference (VREFOUT).
It is suitable for driving the VREFIN pin, but has very lit-
tle fan-out capacity and is not recommended for driving
external circuits.
18
Figure 7. Oscillator Connections
Alternatively, an external clock source can be connect-
ed to the XIN pin.
5.2 Digital Pins
5.2.1 Reset Input
The active-low RESET pin, when asserted, will halt all
CS5467 operations and reset internal hardware regis-
ters and states. When de-asserted, an initialization se-
quence begins, setting default register values.
5.2.2 CPU Clock Output
A logic-level clock output (CPUCLK) is provided at the
crystal frequency to drive an external CPU or microcon-
troller clock. Two phase choices are available.
5.2.3 Interrupt Output
The INT pin indicates an enabled Internal Status regis-
ter ( Status ) bit is set. Status register bits indicate condi-
tions such as data ready, modulator oscillations, low
supply, voltage sag, current faults, numerical overflows,
and result updates.
5.2.4 Energy Pulse Outputs
The CS5467 provides three pins (E1, E2, E3) for pulse
energy outputs. These pins can also be used to output
other conditions, such as voltage1 sign, power fail mon-
itor, or energy sign.
DS714F3
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
CDB5560-2 DEV BOARD FOR CS5560 W/SE INPUT
CDB5571-2 DEV BOARD FOR CS5571 W/SE INPUT
CDB8422 BOARD EVAL FOR CS8422 RCVR
CDB8952T BOARD EVAL FOR CS8952
CDCE906-706PERFEVM EVAL MOD PERFORMANCE CDCE906/706
CEVAL-033 BOARD EVAL FOR CVCO33 .3"X.3"
CF37S COVER FLANGE 37POS FEMALE
CG0402MLC-05LG SUPPRESSOR ESD 5VDC 0402 SMD
相关代理商/技术参数
CDB5471 制造商:Cirrus Logic 功能描述:Tools Development kit Kit Con
CDB5480U-Z 功能描述:电源管理IC开发工具 CS5480 Eval Board RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V
CDB5484U-Z 功能描述:电源管理IC开发工具 CS5484 Eval Board RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V
CDB5490U-Z 功能描述:电源管理IC开发工具 CS5490 Eval Board RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V
CDB5501 制造商:Cirrus Logic 功能描述:EVAL BOARD FOR CS5501 - Bulk
CDB5503 制造商:Cirrus Logic 功能描述:EVAL BOARD FOR CS5503 - Bulk
CDB5504 制造商:CIRRUS 制造商全称:Cirrus Logic 功能描述:Low Power, 20-Bit A/D Converter
CDB5505 制造商:Cirrus Logic 功能描述:EVAL BD FOR CS5505 - Bulk